If you’ve ever wondered how to wire up a concrete block house, then you’re in the right spot. Concrete block houses are popular because of their durability, cost-effectiveness, and ease of construction. If you choose to build your own concrete block house, it can be simple and easy with the right materials and some basic knowledge about electrical wiring. This content is presented by https://accurehome.com/
In this article I will explain what materials and tools are needed to wire up a concrete block house as well as provide some tips on where to best place your outlets, switches and other electrical components so they provide maximum functionality while also being safe for everyone who uses them in the home or business.
How to wiring up a concrete block house?
To wire up your concrete block house, you need to follow the steps below:
Dig your trenches
While it’s important to dig trenches for the electrical wiring, it’s even more important to seal them. You can do this by putting in a 2-inch layer of landscape fabric or plastic sheeting and filling that with gravel. Then, place a layer of concrete over that. This will protect your lawn from being damaged by the trench. Discover now: How to move out of a toxic home
Install the conduit
It’s time to install the conduit. The conduit is a metal pipe that runs from your service panel to the switch box. A 1/2-inch diameter metal pipe is usually used for this job, but you might want to check with a professional electrician before buying conduit (or any other electrical supplies) so that you can buy what they recommend.
The best place to run your conduit is outside of your house, through a hole in your foundation, around the end of your porch or deck and into an interior wall where it will emerge inside near an electrical outlet or light fixture. If possible, bury it about two feet deep so that it won’t be damaged or broken when heavy snow falls on top of it during wintertime!
Run the wires
When you’re wiring up a home, it’s important to know the difference between cables and wires. A cable is a bunch of wires that are all bundled together, while a wire is one single strand of copper or aluminum.
To run your wires through the conduit, you’ll need to cut them down to size and strip off their insulation. The easiest way to do this is with a wire stripper tool.
Then connect the wires with cable ties (which are basically just plastic zip-ties) so they stay in place while running through conduits or around corners. Be sure not to use too many ties though—you don’t want your cables getting too short!
Pour concrete into the trenches
The next step is to pour concrete into the trenches. It’s important to make sure that your trenches are straight, so you’ll need to use a level and a shovel. The amount of concrete you should use depends on how much space there is between each block. If there’s enough room for two or three blocks, you should fill up the entire trench with concrete; if not, then don’t pour too much in or else it can cause damage when trying to put down more blocks later on (and who wants a damaged house?).
Cut into the wall from a service panel location
The important step to wiring a concrete block house is to cut an access hole from the service panel location. To do this, use a saw to cut into the wall from the service panel location. Make sure that the hole is big enough for wires and cables to pass through without being squished. Also make sure that it’s level with ground, floor and ceiling so that you don’t have problems later on when trying to install fixtures or power outlets.
Safety alerts
-If you’re going to cut into the wall, make sure that you wear protective gear like goggles and gloves.
-Don’t cut too close to your head or body so that you don’t hit yourself with falling debris.
-If you’re not sure how to cut into the wall, it’s best to hire a professional electrician to help. He or she will know how to do this safely and efficiently.
-If you’re going to install an outlet, make sure that you know what type of wiring is in your wall. If it’s copper, then it’s possible to use a nail as an attachment point for the wires. For other types of wire (like aluminum), you will need to use a metal stud and screws.
Conclusion
Wiring up a concrete block house is not something that you should try to do on your own. It’s dangerous and can cause serious injury or even death. If you have any questions about wiring up a concrete block house, please contact an electrician for assistance.