If you’ve never tried to snake a bathtub, you might not know that it can be quite challenging! You really don’t want to start with a wet tub because the water will make the task even more difficult and dangerous. Thankfully, this blog article breaks down how you can now strategically start your tub in order for the job to go smoothly.
What is the process of snakeing a bathtub?
If you are like most people, you probably do not know how to snake a bathtub. It may seem like a simple task, but if done improperly, it can lead to disaster. Here is the process of snakeing a bathtub:
1. Measure the circumference of the tub. This is important because you will need to make sure the snake fits snugly around the tub.
2. Cut a piece of PVC pipe that is slightly larger than the circumference of the tub. Make sure the pipe is long enough so that you can extend it all the way around the tub. (You can use a hacksaw or a sawzall to cut the pipe.) Get info about elephant decor.
3. Fit the PVC pipe around the tub and attach it at both ends with zip ties or screws. Make sure that the pipe is tight against the sides of the tub so that water cannot escape.
4. Start filling up the bathtub with water and wait until it reaches normal bathtub levels before plugging in your snake. Turn on your snake and wait for it to reach full length before pulling it back down again. (Make sure you have enough slack in your cord or wires so that it can be stretched.)
5. When you have filled up your bathtub, turn off your snake so that the water drains out of the tub and you can fill it up again. (If you don’t drain the tub first, then your snake could overheat or burn out.)
6. Once the tub is full, plug in your snake and wait for the water level to rise by itself. After a few hours, check that it has reached normal bathtub levels and repeat this process until the tub is full. Look at the ceiling decorations.
What are the benefits of sabatoging your landlord’s efforts?
When you sabatoge your landlord’s efforts to fix a broken bathtub, there are a number of benefits that come with it. First and foremost, you’ll save yourself time and money. If your landlord has to remove the tub themselves, they’ll likely have to pay for a contractor or labor service. In addition, sabatoging can make your tenant feel more secure in their home. By making it difficult for your landlord to install a new bathtub, you can make them more hesitant about changing the lease or seeking other ways to harass you. Finally, sabatoging can send a message that you’re not going to stand for harassment from your landlord. Discover diy concrete pool.
How to snake a bathtub at home
If your bathtub is in dire need of a repair or just doesn’t seem to be draining properly, you can easily snake it yourself. Here’s how:
1. Remove the bathtub drain and cover with a piece of plywood or a sturdy stool.
2. Mark the location of the drain pipe on the wall above and below the tub using a bright marker or paint pen.
3. Cut a 24″ long PVC pipe using a hacksaw or tubing cutter. The diameter of the pipe should be about 1/2″.
4. Thread the end of the PVC pipe through the hole in the drain and then pull it tight so that it forms a U-shape. Make sure that the open end of the pipe is facing down and against the wall.
5. Push two 1-by-4s horizontally into each side of the U-shape from above and below, so that they form platforms for your feet to stand on while you work. This will keep you from being submerged in water while you snake the bathtub.
6. Insert your arms into the ends of the U-shape and snake the bathtub upward until it reaches its original location on the wall . You may need to support the PVC pipe with your hand as you snake it. When the bathtub reaches its original location, lock nuts will hold it in place.
7. Remove the clamps that held your drain pan to the sink and replace them with new ones.
8. Your bathtub is now complete! Find out germinating seeds in paper towel.
Proper tub preparation and tools required
If you’re thinking about snake cleaning your bathtub, here’s what you’ll need: a snake, a bucket, some soap, and water. Here’s how to do it:
1. Disconnect the drain and fill the bucket halfway with water.
2. Position the snake so that the head is submerged in the water and the body is hanging over the edge of the tub.
3. Turn on the faucet and slowly guide the snake around the tub while keeping an eye on the end of its body. The goal is to move soap suds into all corners and crevices of the tub.
4. Move on to another section if you’ve finished cleaning it or let the snake rest in the bucket for a few minutes to clean itself.
Conclusion
The drain is backed up or the tub is just too high to reach, be sure to follow these simple steps. First, measure how far the end of the snake needs to go down into the drain. Then, mark that spot on the wall or ceiling using painter’s tape. Next, use your locating tool (if you have one) and line up the top of your snake with that marker. Finally, lower your snake into the drain until it reaches your marked spot and tighten all of its screws accordingly. You’ll now be able to easily snake that bathtub without any fuss!